TBTUTM-1000CU
TBTSCIETECH
Availability: | |
---|---|
1. Introduction:
TBTUTM-1000CU-I hydraulic universal testing machine, is used to test various high strength metallic & non-metallic materials for tension, compression, bending and shearing strength.
2. Related Standards
GB228.1-2010, GB/T228.1-2010, ISO6892-1998, EN10002-1:2001, and ASTM
1. Introduction:
TBTUTM-1000CU-I hydraulic universal testing machine, is used to test various high strength metallic & non-metallic materials for tension, compression, bending and shearing strength.
2. Related Standards
GB228.1-2010, GB/T228.1-2010, ISO6892-1998, EN10002-1:2001, and ASTM
1. The rigid loading frame is with 4-columns (or 2-columns optional) and 2 screw rods, with upper test space for tensile and lower for compression, bending or shearing.
2. The middle cross-head with built-in worm-gearing is driven by motor for upward & downward moving instead of normal chain transmission to adjust vertical testing space, this greatly reduce back-lash and get more accurate & repeatable test results with displayed test curve smooth & stable.
3. There are multi-level positioning notches on columns for easily adjust upper cross-head to match different specimen height.
4. With front-opening hydraulic wedge grips, it is easier to fasten specimen firmly.
5. Cylinder is mounted at bottom of machine to get better working gravity.
6. Servo oil source system configured with electro-hydraulic servo valve and high-pressure gear pump to get excellent performance.
7. The PC controller with 2-channel digital amplifier enables digital closed-loop control of test force, displacement, stress, strain, etc.
By "Editing" function it enables the test process to be expanded as needed to fulfill any kind of complex editing with control mode switching, meets a variety of international standards.
1. The rigid loading frame is with 4-columns (or 2-columns optional) and 2 screw rods, with upper test space for tensile and lower for compression, bending or shearing.
2. The middle cross-head with built-in worm-gearing is driven by motor for upward & downward moving instead of normal chain transmission to adjust vertical testing space, this greatly reduce back-lash and get more accurate & repeatable test results with displayed test curve smooth & stable.
3. There are multi-level positioning notches on columns for easily adjust upper cross-head to match different specimen height.
4. With front-opening hydraulic wedge grips, it is easier to fasten specimen firmly.
5. Cylinder is mounted at bottom of machine to get better working gravity.
6. Servo oil source system configured with electro-hydraulic servo valve and high-pressure gear pump to get excellent performance.
7. The PC controller with 2-channel digital amplifier enables digital closed-loop control of test force, displacement, stress, strain, etc.
By "Editing" function it enables the test process to be expanded as needed to fulfill any kind of complex editing with control mode switching, meets a variety of international standards.
Maximum load | 1000kN |
Load measurement range | 2%-100%Fs (20kN-1000kN) |
Load accuracy | ±1% |
Displacement measurement resolution | 0.01mm |
Deformation measurement error | ±0.5%F.S |
Test speed control range | 0.1-50mm/min |
Control range of stress speed: | 1-60MPa/S |
Maximum tensile space | 850mm (including piston stroke) |
Maximum compression space | 850mm (including piston stroke) |
Column distance | 630mm |
Flat jaw | 0-40mm |
Clamping width of flat specimen(mm) | 120 |
Round jaw | φ13-φ60mm |
Platen size | 205*205mm |
Bending span | 100-600 mm |
Bending width: | 140mm |
Bending roller diameter: | φ40mm |
Piston stroke: | 250mm |
Clamping method: | hydraulic clamping |
Dimensional size: main unit | Around 1225x750x2640mm |
Control cabinet | Around 1140x700x930mm |
Power Supply | 380V 50HZ (three-phase four-wire) |
Maximum load | 1000kN |
Load measurement range | 2%-100%Fs (20kN-1000kN) |
Load accuracy | ±1% |
Displacement measurement resolution | 0.01mm |
Deformation measurement error | ±0.5%F.S |
Test speed control range | 0.1-50mm/min |
Control range of stress speed: | 1-60MPa/S |
Maximum tensile space | 850mm (including piston stroke) |
Maximum compression space | 850mm (including piston stroke) |
Column distance | 630mm |
Flat jaw | 0-40mm |
Clamping width of flat specimen(mm) | 120 |
Round jaw | φ13-φ60mm |
Platen size | 205*205mm |
Bending span | 100-600 mm |
Bending width: | 140mm |
Bending roller diameter: | φ40mm |
Piston stroke: | 250mm |
Clamping method: | hydraulic clamping |
Dimensional size: main unit | Around 1225x750x2640mm |
Control cabinet | Around 1140x700x930mm |
Power Supply | 380V 50HZ (three-phase four-wire) |
1. Loading frame with cylinder mounted lower, with worm-gear drive...... 1 set
2. Control cabinet with ow noise high pressure gear pump ......................1 set
3. Italian ATOS valve ...................................................................................1 set
4. Italy MARZOCCHI gear pump ....................................................................1 set
5. Special cylinder Multi-stage precision oil filter system..............................1 set
6. Dual channel programmable amplifier.......................................................1 set
7. High-precision oil pressure sensor ............................................. ............1 set
8. Extensometer (YYU25/100) .......................................................................1 set
9. Handheld controller ....................................................................................1 pc
10. Linear displacement measuring system ...................................................1 set
10. A set of accessories:
10.1 Tension clamping jaw for flat (0-20mm,20-40mm) ..........................1 set each
10.2 Tension clamping jaw for round (φ13-φ26mm, φ26-φ40mm,φ40-φ60mm)......1 set each
10.3 Compression clamping jaw (205*205mm) .........................................1 set
10.4 Bending device (Indenter diameter 40mm) ..........................................1 set
11. Special control software for testing .........................................................1 set
12. Lenovo PC ................................................................................................1 set
13. HP A4 printer ...........................................................................................1 set
1. Loading frame with cylinder mounted lower, with worm-gear drive...... 1 set
2. Control cabinet with ow noise high pressure gear pump ......................1 set
3. Italian ATOS valve ...................................................................................1 set
4. Italy MARZOCCHI gear pump ....................................................................1 set
5. Special cylinder Multi-stage precision oil filter system..............................1 set
6. Dual channel programmable amplifier.......................................................1 set
7. High-precision oil pressure sensor ............................................. ............1 set
8. Extensometer (YYU25/100) .......................................................................1 set
9. Handheld controller ....................................................................................1 pc
10. Linear displacement measuring system ...................................................1 set
10. A set of accessories:
10.1 Tension clamping jaw for flat (0-20mm,20-40mm) ..........................1 set each
10.2 Tension clamping jaw for round (φ13-φ26mm, φ26-φ40mm,φ40-φ60mm)......1 set each
10.3 Compression clamping jaw (205*205mm) .........................................1 set
10.4 Bending device (Indenter diameter 40mm) ..........................................1 set
11. Special control software for testing .........................................................1 set
12. Lenovo PC ................................................................................................1 set
13. HP A4 printer ...........................................................................................1 set
content is empty!